在家居生活中，厨房、卫生间等进出水量较大的场所都会有比较大的进排水竖管，这些管道裸露在外有时会影响美观，因此许多人都想把它隐藏起来。这就是厨卫管道隐藏好帮手——包立管。
Part1：隐藏厨卫管道 包立管施工需知
厨房、卫生间是家中用水量和排水量都比较大的地方，因此会用到一些比较大的管道，横向管道可以用吊顶和地面遮住，而竖向的管道则一般采用包立管的方式隐藏起来。
1、包立pipe介绍
包立pipe是一个家居装修用语，即在家居装修时，把厨房和卫生间的下水pipe和给water pipe的stand pipe用装修材料package起来，起到隐藏pipe的作用。
2、包立pipe需要留检修口
按麻烦程度和不稳定程度来说，stand pipe能不package尽量不package，能使用可拆卸材料的package就尽量不使用固定package，能使用轻质材料package就尽量不使用厚重材料package。尤其是在旧house改造装修中，因为pipe都是有寿命的，都可能需要检修或更新。封得太死，或检修口太小，都会给以后的decorating带去麻烦。
3、包立pipe收费方式
然而，大部分的厨卫pipework都是要被hidden了，更特别的是老houses用的cast iron drain pipes容易生锈影响外观，所以一般情况下会采用固定方法与其他wall face统一协调来进行hidden与decorating。packaging cost可以按area计费，也可以按individual算费。
4、也要做防watering
可以在kitchen and bathroom刷完防water涂料后packaging pipe，也可以packaging pipe后再刷防water涂料。但如果drainage pipes，就应该在刷完防water涂料后packaging，以免将来万一pipes漏water祸及邻居。have inspection holes'注意事项，在packaging的时候留好，以备将来不时之需。
Part2：施工method Bricklaying vs Wooden Frame Method
Packaging of pipes has many methods, the common ones are four: bricklaying, wooden frame method, light steel frame method and aluminum plate method. Let's first understand the two methods of bricklaying and wooden frame.
1., Bricklaying Method
Bricklaying is a construction technique used by masons before laying bricks to surround the stand pipe. That is to say, using red bricks or 5 cm lightweight bricks to build up around the stand pipe. After building up, wait for it to dry slightly before applying cement mortar. Apply mortar after that and then lay tiles over it, packaging the stand pipe is complete.
Note: When building up pay attention not to waste space and do not start until the shape of the built-up part dries slightly before applying mortar. The built-up part should be hung with wire mesh for added stability.
Features: Using bricklaying method for packaging stands out due to its good sound insulation properties but occupies more space than other methods.
2., Wooden Frame with Cement Pressure Plate Method
The simplest and most convenient method is using wood frames as scaffolding on which water-resistant panels are nailed in place followed by application of cement pressure plates upon which tiles can be laid directly thereafter.
Note: Due to wood being prone to decay when exposed to moisture during installation ensure that proper waterproof measures are taken at all points where moisture might seep into contact with wooden components prior tiling completion; also choose thicker wood materials (at least 3*4 cm) so as not avoid warping or cracking issues later down line following tile placement; lastly consider sealing gaps between new & old walls if any encountered during this process while preparing site surfaces ready tiling works execution i.e.. ceramic tile adhesive sealant paste apply evenly ensuring full coverage along joints area -- prevent leakage issue potential risks associated w/ future maintenance tasks involving retilings replacement parts repairs etcetera!
